Cher client,
voici nos nouveautés et soldes:
14.99 EUR*
Art.-no. MU_N-H00030
Modellbahn Union
dimensions (LBH): 80 x 45 x 50 mm
|
164.00 EUR*
Art.-no. Fleischmann_738803
Fleischmann
Locomotive électrique série 185.2 de la Lokomotion. Époque VI. Modèle réduit avec inscription et peinture fidèles au modèle original. Fenêtres encastrées. Châssis en métal coulé sous pression. Moteur avec masse d'inertie. Entraînement de 4 essieux. Deux bandages d'adhérence. Interface selon la norme NEM 662 (Next18) pour l'enfichage d'un décodeur. Boîtier d'attelage selon NEM 355 avec coulisse d'attelage court. Fanal avant à trois feux DEL inversé blanc/rouge en fonction du sens de marche. Fanal avant peut être éteint de tout ou partie par des tôles de contact. Avec affichage lumineux de la destination du train.
|
244.00 EUR*
Art.-no. Fleischmann_738871
Fleischmann
Locomotive électrique 146 247-2 de la DB AG - "Pour un nouveau monde connecté et intelligent". Époque VI. Modèle réduit avec décodeur numérique à compensation de charge intégré et équippé départ usine d'une sonorisation authentique. Modèle réduit avec inscription et peinture fidèles au modèle original. Fenêtres encastrées. Châssis en métal coulé sous pression. Moteur avec masse d'inertie. Entraînement de 4 essieux. Deux bandages d'adhérence. Interface selon la norme NEM 662 (Next18) pour l'enfichage d'un décodeur. Boîtier d'attelage selon NEM 355 avec coulisse d'attelage court. Fanal avant à trois feux DEL inversé blanc/rouge en fonction du sens de marche. Avec affichage lumineux de la destination du train.
|
44.90 EUR*
Art.-no. Fleischmann_864305
Fleischmann
Voiture de 2ème classe pour train rapide, construction type Bm234, de la Deutsche Bundesbahn. Époque IV. Modèle réduit avec aménagement intérieur, fenêtres encastrées et cinématique d'attelage court. Peinture et inscriptions fidèles au modèle réel. Avec feux arrière électroniques qui s'allument uniquement dans une seule direction. Si le train part dans la direction opposée, le feu rouge s'éteindra automatiquement. L'éclairage intérieur peut être monté ultérieurement. Boîtier d'attelage selon NEM 355. |
29.99 EUR*
Art.-no. DCC-Concepts_CB1DIP
DCC Concepts
Introducing Cobalt-iP Digital – Cobalt-iP Digital is a new Cobalt DCC-on board product that adds on-board DCC control to the very best features of Cobalt Classic-O and Cobalt -iP to create the best ever digital-ready point motor. With Cobalt-iP Digital, you can have your cake and eat it too, because it is 100% ready to go in digital format, yet it will also allow you to have a classic control panel with a choice of either one or two push-button switches per turnout… Super low current draw means you can use complex pre-set routes using the abilities already built in to most quality DCC control systems with no need to add anything else!
A general overview of Cobalt and Cobalt-iP ranges: Cobalt Point Motors are the most reliable and powerful point motors available and they are exceptionally gentle on your point-work. A movable fulcrum allows easy adjustment of blade closure pressure and ensures that throw is easy to adjust irrespective of scale, type of point-work or thickness of baseboards. |
159.99 EUR*
Art.-no. DCC-Concepts_CB6DIP
DCC Concepts
Introducing Cobalt-iP Digital – Cobalt-iP Digital is a new Cobalt DCC-on board product that adds on-board DCC control to the very best features of Cobalt Classic-O and Cobalt -iP to create the best ever digital-ready point motor. With Cobalt-iP Digital, you can have your cake and eat it too, because it is 100% ready to go in digital format, yet it will also allow you to have a classic control panel with a choice of either one or two push-button switches per turnout… Super low current draw means you can use complex pre-set routes using the abilities already built in to most quality DCC control systems with no need to add anything else!
A general overview of Cobalt and Cobalt-iP ranges: Cobalt Point Motors are the most reliable and powerful point motors available and they are exceptionally gentle on your point-work. A movable fulcrum allows easy adjustment of blade closure pressure and ensures that throw is easy to adjust irrespective of scale, type of point-work or thickness of baseboards. |
299.99 EUR*
Art.-no. DCC-Concepts_CB12DIP
DCC Concepts
Introducing Cobalt-iP Digital – Cobalt-iP Digital is a new Cobalt DCC-on board product that adds on-board DCC control to the very best features of Cobalt Classic-O and Cobalt -iP to create the best ever digital-ready point motor. With Cobalt-iP Digital, you can have your cake and eat it too, because it is 100% ready to go in digital format, yet it will also allow you to have a classic control panel with a choice of either one or two push-button switches per turnout… Super low current draw means you can use complex pre-set routes using the abilities already built in to most quality DCC control systems with no need to add anything else!
A general overview of Cobalt and Cobalt-iP ranges: Cobalt Point Motors are the most reliable and powerful point motors available and they are exceptionally gentle on your point-work. A movable fulcrum allows easy adjustment of blade closure pressure and ensures that throw is easy to adjust irrespective of scale, type of point-work or thickness of baseboards. |
136.80 EUR*
Art.-no. DH_DH-X2X
Doehler & Haass
Diese neu entwickelte X2X-Box ermöglicht es, vorhandene Fahr- oder Stellregler wie die Roco Maus, das Roco RouteControl oder den Lenz LH90/LH100 an unsere Future-Central-Control (FCC) anzuschließen. Dazu bietet die X2X-Box auf der einen Seite Anschlüsse für XpressNet™ Geräte und auf der anderen Seite Anschlüsse für zwei SelecTRIX Busse. Dadurch kann die X2X-Box für folgendes verwendet werden: |
69.99 EUR*
Art.-no. Fleischmann_Multimaus-allein
Fleischmann
promotion temporaire jusqu´à épuisement des stocks, prix d´un coffret de start sans emballge |
56.05 EUR*
Art.-no. DH_DH-Bus-V
Doehler & Haass
9-facher SX-Busverteiler mit vier SX-Bus-Buchsen, drei Anschlußbuchsen für Mobile-Stations und zwei Modul-Verbindungs-Stiftleisten. |
70.30 EUR*
Art.-no. DH_DH-FCC-Netzteil
Doehler & Haass
Abb. ähnlich Universal Netzteil 12 - 24 V / 100 W passend für Programmer, Future-Central-Control (FCC), Funktionsdecoder und Power-Pack.
Eingangsspannung (AC Input): 110 - 240 V / max. 1,3 A / 50 - 60 Hz Ausgangsspannung (DC Output): Einstellbar von 12 V bis 24 V (12, 15, 16, 18, 19, 20, 22, 24 V) / max. 5 A Ausgangsleistung: Max. 100W USB-Anschluss: 5 V / 1 A (kann gleichzeitig mitbenutzt werden) |
9.50 EUR*
Art.-no. DH_DH-403-3
Doehler & Haass
length 1,0 m |
9.03 EUR*
Art.-no. DH_DH-403-2
Doehler & Haass
length 0,6 m |
7.99 EUR*
Art.-no. DH_DH-403-1
Doehler & Haass
length 0,3 m |
32.99 EUR*
Art.-no. ESU_51822
ESU
With the SwitchPilot V2.0 we present to you an improved version of our well proven accessory decoder. It is a robust multi protocol switch and accessory decoder for controlling up to 4 solenoid accessories (e.g. points) or 8 loads such uncoupling ramps or incandescent lamps (e.g. street lighting, lighting of buildings or points). Due to its intelligent software it can be operated with either DCC or Motorola®. Operating modesThe SwitchPilot can be operated with DCC and Motorola®. It is compatible to the DCC standard and is triggered by accessory commands. In Motorola® mode the possible addresses range from 01 – 127. The digital protocol is detected automatically. FunctionalityThe SwitchPilot can either be powered by the digital command station or by a separate transformer supplying AC or DC. You may connect up to 4 solenoid motors by any of the known manufacturers to its 8 transistor outputs with a maximum continuous current of 1A. In order to prevent blowing the coil of a solenoid without end position contacts the switch-on time can be adjusted separately for each output from 0.1 sec to 1 second. The SwitchPilot behaves in this mode k83 compatible. Servo controlThe SwitchPilot V2.0 can do more: in addition to the 4 transistor outputs it can control two conventional RC servos. Speed of movement as well as the end positions can be individually programmed. This facilitates particularly prototypical, slow and powerful point motors regardless of the brand of track system. This is especially valuable for driving semaphore signals or the gates at level crossings. If so desired, the servo pulse can be turned off once the end position has been reached. The power supply to the servo can also be interrupted in order to prevent the humming of some low cost servos. FeedbackThe SwitchPilot can, as the ideal “partner” of the ECoS, provide real feedback of the actual setting of the points. This requires mechanical preparation of the point respectively the point motor: finally you have certainty that your point is really set in the desired position! Setting parametersThe SwitchPilot can be flexibly programmed: on the one hand it supports all DCC programming modes including POM (Programming on the Main). Provided there is a command station with a programming output, all settings can be monitored and adjusted. Alternatively you may enter the address also with the aid of the programming button mounted directly on the SwitchPilot: press the button – trigger a switch command at the command station – done! SwitchPilot ExtensionDo you need some relay outputs in addition to the servo outputs, since you intend to polarize the frog, for instance, or switch off the track voltage within the signal line section? Then you should extend your SwitchPilot Servo with the SwitchPilot Extension relay module: one of its four twin-relay contacts switches simultaneously to the servo and can be used for potential-free load swichting – ideal for tricky circuitry! ProtectionAs it has been the case with our loco decoders, in the design phase´s greatest emphasis has been placed upon near indestructibility of the SwitchPilot Servo decoders. That means ESU quality is also built into our stationary decoders, now and in the future! You can rely on it! Future proofThe internal software of the SwitchPilot V2.0 can be replaced by a more up-to-date version at any time. This is done with the aid of the ESU LokProgrammer. That way everything remains current in case of changes in the standards and you may also profit from new functions. |
38.99 EUR*
Art.-no. ESU_51820
ESU
SwitchPilot V2.0, accessory decoder for 4 twin coils magnetic, 2 x Servo, DCC/MM, 1A With the SwitchPilot V2.0 we present to you an improved version of our well proven accessory decoder. It is a robust multi protocol switch and accessory decoder for controlling up to 4 solenoid accessories (e.g. points) or 8 loads such uncoupling ramps or incandescent lamps (e.g. street lighting, lighting of buildings or points). Due to its intelligent software it can be operated with either DCC or Motorola®. |
32.99 EUR*
Art.-no. ESU_51801
ESU
SwitchPilot Extension, 4 twin-relays (DPDT) output, 2A each, extension for Switch Pilot Family If required, SwitchPilot can be augmented with the SwitchPilot Extension Modul: Plugged in at the side of the SwitchPilot, it offers four relay-driven outputs, used for switching potential-free loads, or for polarizing the frog; the ideal supplement for tricky circuitry. |
15.99 EUR*
Art.-no. ESU_51804
ESU
Servo Motor, precision mini-servo, micro-controlled with plastic gearing, incl. mounting kit The Precision Servo Motor is a high-performance and noiseless actuator, introduced by ESU, suitable for the SwitchPilot decoders. It uses a highly-developed remote control (RC) technique and is perfectly suited for setting in motion all kinds of scenes on your layout. ESU has put all the experience gained with the previous servo motor into the new Precision version, which is better than other servo products, to offer a solution for all the demands of model railroaders. Applications The most important application regarding the Precision Servo Motor is to throw points. With the help of the Precision Servo Motor you are able to move your model railway switches like the original ones: the switch blade moves slowly and powerfully from one position to another.While doing this the Precision Servo motor works almost noiselessly due to the precision gearing made of long-lasting plastic. It is mere child´s play to motorize railway crossings via the Precision Servo motor and the SwitchPilot Servo. At last you can let the gates down at your keyboard in due time. Furthermore the Servo motor enables you to open and close the doors of your engine shed by remote control. Thanks to its new electronics the ESU Precision Servo Motor moves considerably smoother than other servos, as the ESU product has been optimized for slow motions. Mini servo The most important component of the Precision Servo Motor is a tiny, 9-gram-light mini servo which has been specially developed and optimized for all demands of a model railway layout. Despite its small dimensions of only 26 mm x 13 mm x 24 mm, it reaches a power of up to 1.0 kg/cm. Its cable length of 30cm (almost twice as long as cables of other standard servos on the market) allows for a longer distance between the servo motor and decoder. Beyond that, an electronic processor-controlled servo enables a precise heading for the required position without bucking - very important for garage doors. The closed current requirements of the electronics have been mottled compared to the previous servo motor which preserves the decoder. However, one of the most important improvements of the new Precision Servo Motor has to do with the switching-on: The well-known tremor when switching on the layout, which occurs with a lot of conventional RC-servos, is 100% choked during every operation mode. You will hear absolutely nothing from the servo when switching your layout on, no railway crossing will bounce. Accessories To make the application of the Servo motor as easy as possible, we include substantial accessories with delivery, which are especially adjusted to our customers´ needs: among some, diverse control horns, there is a special servo horn for a direct insert of the controlling wire. The controlling wire is, of course, included as well as the mounting screws. The most important accessory is a special servo holder: it enables you to install the Servo Motor either horizontally or vertically - depending on the application. |
19.99 EUR*
Art.-no. ESU_51805
ESU
Servo Motor, precision mini-servo, micro-controlled with metal gearing, incl. mounting kit ESU proudly presents a further, newly-developed servo motor for all ambitious model railway fans. The „Precision Servo Motor - Metal“ is preferred by all model railroaders who look for a powerful servo with metal gearing. Thanks to its metal gearing the servo is able to lift nearly twice the load (1.8 kg) of its plastic gearing brother. Moreover, the „Precision Servo Motor - Metal“ is appropriate for all situations in which splicing and beating claim high mechanical requirements from the servo and where the sound development does not play such an important role. With the same measurements as the Precision Servo Motor, the metal gearing is also equipped with the new, micro-processed control electronics for a precise, sensitive heading to the required position. Therefore the impuls suppression makes sure that there won´t be any tremors on the layout when you switch it on. The 30cm cables makes easy wiring possible. Also, the „Precision Servo Motor - Metal“ comes with innovative and well-proven accessories such as a servo holder and controlling wires. |
3.99 EUR*
Art.-no. ESU_51810
ESU
Servo Extension Cable, 3-pole J/R plug on socket J/R / Futaba, Length: 75cm
|
53.50 EUR
(PVC*)
34.99 EUR*
Art.-no. MW-Modell_N-IT-403d
MW-Modell
promotion temporaire jusqu´à épuisement des stocks |
62.50 EUR
(PVC*)
39.99 EUR*
Art.-no. MW-Modell_N-IT-404d
MW-Modell
promotion temporaire jusqu´à épuisement des stocks |
54.90 EUR
(PVC*)
39.99 EUR*
Art.-no. MW-Modell_N-IT-401k
MW-Modell
FS Dienstwagen/Bauzugwagen Typ Va (ex F) Zum Modell: Es handelt sich um eine komplette Neukonstruktion. Erstmals in Spur N werden diese Wagen maßstäblich gefertigt. Dank innovativer Technik ist es möglich, die verschiedenen Achslager, die u.a. charakteristisch waren für diese Wagen, im Modell umzusetzen. Einer der beiden Waggons hat Achslager mit 3fach-Federpaketen, der zweite Waggon ist mit Doppel-Federpaketen ausgestattet. Highlights und technische Daten: • exakte Umsetzung im Maßstab 1:160 • LüP 57,5 mm • Gewicht 14 g • unterschiedliche Achslager für Varianten der Epochen 2 , 3 und 4 • einzeln eingesteckte Metall-Puffer • NEM-Normschacht mit Kurzkupplungskinematik • sauber gedruckte, feine Beschriftung • verschiedene Betriebsnummern • made in Germany Hinweis: Für optimale Laufeigenschaften in Kurven empfehlen wir Kurven-Radien ab R2 (228mm) und größer.
|
219.90 EUR
(PVC*)
159.99 EUR*
Art.-no. LS_78037
L.S. Models
avec attelages à élongation |
219.99 EUR
(PVC*)
159.99 EUR*
Art.-no. LS_78038
L.S. Models
avec attelages à élongation |
219.90 EUR
(PVC*)
159.99 EUR*
Art.-no. LS_78040
L.S. Models
avec attelages à élongation |
219.90 EUR
(PVC*)
159.99 EUR*
Art.-no. LS_78041
L.S. Models
avec attelages à élongation |
219.90 EUR
(PVC*)
159.99 EUR*
Art.-no. LS_78042
L.S. Models
avec attelages à élongation |
219.90 EUR
(PVC*)
159.99 EUR*
Art.-no. LS_78043
L.S. Models
avec attelages à élongation |
24.99 EUR*
Art.-no. Artitec_6160062
Artitec
pret et paint, très très bonne qualité |
22.40 EUR*
Art.-no. Artitec_316.050
Artitec
Ready-made |
10.99 EUR*
Art.-no. Artitec_316.042
Artitec
modèle peint et assemblé |
11.40 EUR*
Art.-no. Artitec_316.044
Artitec
modèle peint et assemblé |
6.99 EUR*
Art.-no. Gaugemaster_GM758
Gaugemaster
Contexte de train miniature 3 pièces avec un excellent rapport qualité-prix. L'impression de rasoir est faite sur du papier de haute qualité 150g / m² qui garantit une longue durée de vie. Les dimensions des scènes d'arrière-plan sont de 54 "x 54" (1372mm x 152mm) et sont idéales pour les pistes H0, TT et N, et se composent de 3 sections égales par paquet.
Il y a un total de 8 motifs différents dans deux tailles différentes. Les petits fonds avec les numéros d'article GM75x ont la dimension 1372 x 152mm et le grand GM70x 2744 x 304mm Pour le traitement, nous recommandons la colle suivante: Deluxe View Glue DLAD-61 |
1.30 EUR
(PVC*)
0.99 EUR*
Art.-no. Fleischmann_fl-22222
Fleischmann
neuf, sans emballage
|
Votre dévoué,
Daniel Mrugalski
DM-Toys
www.modellbahnunion.com