Shipping Destination
Shipping Destination
Language:
Decoder DH05C-3 wire DCC + Selectrix
Zoom: hover, original: click
Beschreibung
The latest version with the latest software is always supplied!
Product Features and Functions
- For optional operation with a conventional DC controller, digital systems according to SelecTRIX 1 and 2 or according to the NMRA standard (DCC)
- Switching between analogue and digital operation is automatic
- In digital mode, the last programmed system is used (it is not switched over automatically!)
- SelecTRIX 1 31 speed levels, 100 addresses
- SelecTRIX 2 127 speed steps, 10,000 addresses, 16 additional functions
- DCC short addresses (1-127), long addresses (0001-9999), with 14, 28, 126 speed steps
- Load control of the latest generation, resulting in particularly soft control behavior
- Various control variants for optimal adaptation to the engine
- Internal 127 speed levels
- Adjustable motor frequency (low frequency, 16kHz, 32kHz)
- Block section operation with simple diodes in digital operation
- Light and function outputs can be dimmed and activated analogously
- Shunting gear
- Motor, light and track connections can be exchanged electronically
- All function outputs freely programmable
- Temperature protection
- Reset function for DCC and SX2
- Update capability of the decoder
Micro locomotive decoder 0.5 A:
Operating mode SX1, SX2, DCC, MM, DC analog
Dimensions [mm] 12.9 * 6.7 * 1.4
Total load 0.5 A
Max motor current 0.5A
Max. driving voltage 30 V
LV, LR (dimmable) 150 mA each
AUX1, AUX2 (dimmable) 300 mA each
AUX3, AUX4 unamplified
with SUSI interface (if AUX3/AUX4 deactivated)
The update (the firmware download from the Internet is free) is possible when the decoder is installed on the track (the vehicle does not need to be opened) and is carried out either via the FCC digital center or the programmer. If no appropriate hardware is available, Doehler & Haass will provide a programmer on request.
The DH05C micro locomotive decoder supports braking with asymmetrical digital voltage (four diodes in series and one diode anti-parallel, Lenz ABC), slow travel (with suitable brake modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®).
A connected SUSI sound module must be removed for SX1 programming. It is sufficient to interrupt the supply voltage (red wire) for the time of the SX1 programming. This does not affect the SX2 or DCC programming. The software, firmware and sound data can be downloaded from the Doehler & Haass website .
Product Features and Functions
- For optional operation with a conventional DC controller, digital systems according to SelecTRIX 1 and 2 or according to the NMRA standard (DCC)
- Switching between analogue and digital operation is automatic
- In digital mode, the last programmed system is used (it is not switched over automatically!)
- SelecTRIX 1 31 speed levels, 100 addresses
- SelecTRIX 2 127 speed steps, 10,000 addresses, 16 additional functions
- DCC short addresses (1-127), long addresses (0001-9999), with 14, 28, 126 speed steps
- Load control of the latest generation, resulting in particularly soft control behavior
- Various control variants for optimal adaptation to the engine
- Internal 127 speed levels
- Adjustable motor frequency (low frequency, 16kHz, 32kHz)
- Block section operation with simple diodes in digital operation
- Light and function outputs can be dimmed and activated analogously
- Shunting gear
- Motor, light and track connections can be exchanged electronically
- All function outputs freely programmable
- Temperature protection
- Reset function for DCC and SX2
- Update capability of the decoder
Micro locomotive decoder 0.5 A:
Operating mode SX1, SX2, DCC, MM, DC analog
Dimensions [mm] 12.9 * 6.7 * 1.4
Total load 0.5 A
Max motor current 0.5A
Max. driving voltage 30 V
LV, LR (dimmable) 150 mA each
AUX1, AUX2 (dimmable) 300 mA each
AUX3, AUX4 unamplified
with SUSI interface (if AUX3/AUX4 deactivated)
The update (the firmware download from the Internet is free) is possible when the decoder is installed on the track (the vehicle does not need to be opened) and is carried out either via the FCC digital center or the programmer. If no appropriate hardware is available, Doehler & Haass will provide a programmer on request.
The DH05C micro locomotive decoder supports braking with asymmetrical digital voltage (four diodes in series and one diode anti-parallel, Lenz ABC), slow travel (with suitable brake modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®).
A connected SUSI sound module must be removed for SX1 programming. It is sufficient to interrupt the supply voltage (red wire) for the time of the SX1 programming. This does not affect the SX2 or DCC programming. The software, firmware and sound data can be downloaded from the Doehler & Haass website .