N-Scale 05/2024: Bargains

23.99 EUR^*

Art.-no. DH_PD10MU-3

Doehler & Haass

A new Doehler & Haass decoder developed exclusively for Modellbahn Union / DM-Toys, adapted to the needs of N-gauge model railroaders. As with all comparable Doehler & Haass decoders, the driving characteristics of this decoder are at an excellent level. Two small capacitors are installed on the decoder for driving without data loss. Both the software and the chip itself correspond to the same modern technology as the latest decoders from Doehler & Haass. The decoder, produced in Germany, can be used for both normal DC motors and coreless motors. Switching from analogue to digital operation takes place automatically.

Due to our direct sales and exclusive production, we can offer this decoder in cooperation with Doehler and Haass at a very attractive price.

The vehicle decoders support braking with asymmetrical digital voltage (four diodes in series and one diode anti-parallel, Lenz ABC), slow travel (with suitable braking modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®).

Dimensions: 8.5 x 11.7 x 1.8mm
Total load capacity: 1.0 A
Maximum Motor Current: 1.0A
Maximum driving voltage: 30 V
Light function outputs: LV, LR (dimmable): 150 mA each
Function outputs: AUX1, AUX2 (dimmable): 300 mA each

functions
• For operation with conventional DC traction device, digital systems according to the NMRA standard (DCC)
• Switching between analogue and digital operation is automatic
• Short addresses (1-127), long addresses (0001-9999), with 14, 28, 126 speed steps
• Latest generation load control, resulting in particularly smooth control behavior
• Various control variants for optimum adaptation to the engine
• Internally 127 speed steps
• Adjustable motor frequency (low frequency, 16 kHz, 32 kHz)
• Block section operation with simple diodes in digital operation
• Light and function outputs (partially) dimmable and can be activated analogously
• Shunting gear
• Motor, light and track connections can be exchanged electronically
• All function outputs freely programmable
• Temperature protection
• Reset function for DCC
• The decoder can be updated
• Timer for switching off AUX1 and AUX2

The update (the firmware download from the Internet is free) is possible when the decoder is installed on the track (the vehicle does not need to be opened) and is carried out either via the FCC digital center or the programmer. If no appropriate hardware is available, Doehler & Haass will provide a programmer on request.

The vehicle decoders support braking with asymmetrical digital voltage (four diodes in series and one diode anti-parallel, Lenz ABC), slow travel (with suitable braking modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®).

23.99 EUR^*

Art.-no. DH_PD10MU-4

Doehler & Haass

A new Doehler & Haass decoder developed exclusively for Modellbahn Union / DM-Toys, adapted to the needs of N-gauge model railroaders. As with all comparable Doehler & Haass decoders, the driving characteristics of this decoder are at an excellent level. Two small capacitors are installed on the decoder for driving without data loss. Both the software and the chip itself correspond to the same modern technology as the latest decoders from Doehler & Haass. The decoder, produced in Germany, can be used for both normal DC motors and coreless motors. Switching from analogue to digital operation takes place automatically.

Due to our direct sales and exclusive production, we can offer this decoder in cooperation with Doehler and Haass at a very attractive price.

The vehicle decoders support braking with asymmetrical digital voltage (four diodes in series and one diode anti-parallel, Lenz ABC), slow travel (with suitable braking modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®).

Dimensions: 8.5 x 11.7 x 1.8mm
Total load capacity: 1.0 A
Maximum Motor Current: 1.0A
Maximum driving voltage: 30 V
Light function outputs: LV, LR (dimmable): 150 mA each
Function outputs: AUX1, AUX2 (dimmable): 300 mA each

functions
• For operation with conventional DC traction device, digital systems according to the NMRA standard (DCC)
• Switching between analogue and digital operation is automatic
• Short addresses (1-127), long addresses (0001-9999), with 14, 28, 126 speed steps
• Latest generation load control, resulting in particularly smooth control behavior
• Various control variants for optimum adaptation to the engine
• Internally 127 speed steps
• Adjustable motor frequency (low frequency, 16 kHz, 32 kHz)
• Block section operation with simple diodes in digital operation
• Light and function outputs (partially) dimmable and can be activated analogously
• Shunting gear
• Motor, light and track connections can be exchanged electronically
• All function outputs freely programmable
• Temperature protection
• Reset function for DCC
• The decoder can be updated
• Timer for switching off AUX1 and AUX2

The update (the firmware download from the Internet is free) is possible when the decoder is installed on the track (the vehicle does not need to be opened) and is carried out either via the FCC digital center or the programmer. If no appropriate hardware is available, Doehler & Haass will provide a programmer on request.

The vehicle decoders support braking with asymmetrical digital voltage (four diodes in series and one diode anti-parallel, Lenz ABC), slow travel (with suitable braking modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®).

22.99 EUR^*

Art.-no. DH_PD18MU

Doehler & Haass

A new Doehler & Haass decoder developed exclusively for Modellbahn Union / DM-Toys, adapted to the needs of N-gauge model railroaders. As with all comparable Doehler & Haass decoders, the driving characteristics of this decoder are at an excellent level. Two small capacitors are installed on the decoder for driving without data loss. Both the software and the chip itself correspond to the same modern technology as the latest decoders from Doehler & Haass. The decoder, produced in Germany, can be used for both normal DC motors and coreless motors. Switching from analogue to digital operation takes place automatically. The decoder has only 2 function outputs (AUX1&AUX2), AUX3-6 are not assigned!

Due to our direct sales and exclusive production, we can offer this decoder in cooperation with Doehler and Haass at a very attractive price.

The vehicle decoders support braking with asymmetrical digital voltage (four diodes in series and one diode anti-parallel, Lenz ABC), slow travel (with suitable braking modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®).

Dimensions: 9.0 x 9.7 x 2.9mm
Total load capacity: 1.0 A
Maximum Motor Current: 1.0A
Maximum driving voltage: 30 V
Light function outputs: LV, LR (dimmable): 150 mA each
Function outputs: AUX1, AUX2 (dimmable): 300 mA each

functions
• For operation with conventional DC traction device, digital systems according to the NMRA standard (DCC)
• Switching between analogue and digital operation is automatic
• Short addresses (1-127), long addresses (0001-9999), with 14, 28, 126 speed steps
• Latest generation load control, resulting in particularly smooth control behavior
• Various control variants for optimal adaptation to the engine
• Internally 127 speed steps
• Adjustable motor frequency (low frequency, 16 kHz, 32 kHz)
• Block section operation with simple diodes in digital operation
• Light and function outputs (partially) dimmable and can be activated analogously
• Shunting gear
• Motor, light and track connections can be exchanged electronically
• All function outputs freely programmable
• Temperature protection
• Reset function for DCC
• The decoder can be updated
• Timer for switching off AUX1 and AUX2

The update (the firmware download from the Internet is free) is possible when the decoder is installed on the track (the vehicle does not need to be opened) and is carried out either via the FCC digital center or the programmer. If no appropriate hardware is available, Doehler & Haass will provide a programmer on request.

The vehicle decoders support braking with asymmetrical digital voltage (four diodes in series and one diode anti-parallel, Lenz ABC), slow travel (with suitable braking modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®).

74.79 EUR (RRP*)

59.99 EUR^*

Art.-no. Tomix_6426

Tomix

rail vacuum cleaner

The classic in a new design! Immediately available, permanently reduced in price!

The rail cleaning trolley can be used for cleaning, as a vacuum cleaner or as a grinding trolley. 3 grinding and cleaning pads are included in the packaging. This wagon is absolutely indispensable and saves tiresome rail cleaning work, can also be used in places that are difficult to access. We directly recommend the use of 2 trolleys. You can have one permanently polished and use the other directly behind it as a vacuum cleaner.

Functionality:
It is operated using 12V DC voltage and being pulled or pushed by a motorized vehicle. The analogue version is not suitable for digital model railways, as the permanently applied current overloads the motor and triggers the heat protection switch.

You can purchase the car directly from us in the digital version. We convert the car with a Doehler and Haass decoder which we solder.

Cart Length: 120mm

269.90 EUR (RRP*)

179.99 EUR^*

Art.-no. REE_NW-167

REE Models

Control cars and motor cars have their own decoder interfaces. In our digital versions, of course, we install two decoders per train so that the light change is also correctly displayed digitally.

525.90 EUR (RRP*)

299.99 EUR^*

Art.-no. Jaegerndorfer_JC75510

Jägerndorfer

- 3-light headlights
- 4-window front with high roof
- Model with changing lights
- Train with 2 power cars, 1 restaurant car and 2 intermediate cars
- 2 decoders are required for operation in DCC mode
- Printed Vindobona signs

The 5045 and 5145 series of the Austrian Federal Railways are express train diesel multiple units built in the 1950s and known as the Blauer Blitz. The vehicles were initially used primarily in international and national express train traffic, the express railcar trains (TS) “Vindobona” Vienna–Praha–Berlin. For many years they also ran domestic express connections between Vienna and Villach and between Vienna and Graz via the Southern Railway. Several vehicles have been preserved as museum pieces. They are owned by AUSTROVAPOR, are looked after by the “Club Blauer Blitz” in the Strasshof Railway Museum and could be chartered in any configuration for special trips until 2009. Since 2016, a two-part railcar train has been available again for nostalgic trips after partial repairs.

614.90 EUR (RRP*)

399.99 EUR^*

Art.-no. Jaegerndorfer_JC75512

Jägerndorfer

- 3-light headlights
- 4-window front with high roof
- Model with changing lights
- Train with 2 power cars, 1 restaurant car and 2 intermediate cars
- Model with sound DCC Digital
- Printed Vindobona signs

The 5045 and 5145 series of the Austrian Federal Railways are express train diesel multiple units built in the 1950s and known as the Blauer Blitz. The vehicles were initially used primarily in international and national express train traffic, the express railcar trains (TS) "Vindobona" Vienna–Praha–Berlin. For many years they also ran domestic express connections between Vienna and Villach and between Vienna and Graz via the Southern Railway. Several vehicles have been preserved as museum pieces. They are owned by AUSTROVAPOR, are looked after by the “Club Blauer Blitz” in the Strasshof Railway Museum and could be chartered in any combination for special trips until 2009. Since 2016, a two-part railcar train has been available again for nostalgic trips after partial repairs.

384.90 EUR (RRP*)

199.99 EUR^*

Art.-no. Jaegerndorfer_JC75310

Jägerndorfer

- 4-window front with low roof
- Train with 1 power car, 1 intermediate car and 1 control car
- Model with changing lights
- Control car with 6-pin interface, motor car with Next18 interface

The 5045 and 5145 series of the Austrian Federal Railways are express train diesel multiple units built in the 1950s and known as the Blauer Blitz. The vehicles were initially used primarily in international and national express train traffic; the express railcar train (TS) "Venezia" was in use between Vienna and Venice. For many years they also ran domestic express connections between Vienna and Villach and between Vienna and Graz via the Southern Railway. Several vehicles have been preserved as museum pieces. They are owned by AUSTROVAPOR, are looked after by the “Club Blauer Blitz” in the Strasshof Railway Museum and could be chartered in any combination for special trips until 2009. Since 2016, a two-part railcar train has been available again for nostalgic trips after partial repairs.

528.90 EUR (RRP*)

299.99 EUR^*

Art.-no. Jaegerndorfer_JC75312

Jägerndorfer

- 4-window front with low roof
- Train with 1 power car, 1 intermediate car and 1 control car
- Model with changing lights
- DCC digital sound version

The 5045 and 5145 series of the Austrian Federal Railways are express train diesel multiple units built in the 1950s and known as the Blauer Blitz. The vehicles were initially used primarily in international and national express train traffic; the express railcar train (TS) "Venezia" was in use between Vienna and Venice. For many years they also ran domestic express connections between Vienna and Villach and between Vienna and Graz via the Southern Railway. Several vehicles have been preserved as museum pieces. They are owned by AUSTROVAPOR, are looked after by the “Club Blauer Blitz” in the Strasshof Railway Museum and could be chartered in any combination for special trips until 2009. Since 2016, a two-part railcar train has been available again for nostalgic trips after partial repairs.

32.30 EUR (RRP*)

24.99 EUR^*

Art.-no. Artitec_316.094

Artitec

Artitec ready-made models are handcrafted from resin and etched metal parts. Each model is hand-painted and sometimes slightly weathered. Our models are all unique collectibles.

169.90 EUR (RRP*)

119.99 EUR^*

Art.-no. Arnold_HN4297

Arnold

RCT, 4-part Set of passenger coaches "The Berliner", in ocean blue / beige paint, Ep. IV

149.90 EUR (RRP*)

109.99 EUR^*

Art.-no. Arnold_HN4460

Arnold

RENFE, 3 pcs. Set CIWL passenger coach “Castellano Expreso”, consisting of 1 x baggage car and 2 x sleeping car Lx, Ep. IV

81.90 EUR (RRP*)

49.99 EUR^*

Art.-no. Arnold_HN6608

Arnold

SNCF, 2 pcs. Set 3-axle. Tank car, "BP" Ep. III

49.99 EUR (RRP*)

34.99 EUR^*

Art.-no. Arnold_HNS4332

Arnold

Special model by Arnold for DM-Toys in a strictly limited one-time edition, valid as long as stocks last!

Company numbers: 51 51 88-80 038-4

1.99 EUR^*

Art.-no. DeAgostini_009

DeAgostini

Plastic kit with two painted St. Andrews cross (without tracks).

2.99 EUR^*

Art.-no. DeAgostini_016

DeAgostini

N gauge nickel silver track 100% compatible with Minitrix / Roco / Fleischmann

3.99 EUR^*

Art.-no. DeAgostini_002

DeAgostini

N gauge nickel silver track 100% compatible with Minitrix / Roco / Fleischmann

3.99 EUR^*

Art.-no. DeAgostini_004

DeAgostini

N gauge nickel silver track 100% compatible with Minitrix / Roco / Fleischmann. The 8 tracks make a semicircle. Perfect for helical tracks or the like.

5.99 EUR^*

Art.-no. DeAgostini_026

DeAgostini

N gauge nickel silver track 100% compatible with Minitrix / Roco / Fleischmann. The 8 tracks make a whole circle. Perfect for helical tracks or the like.

5.99 EUR^*

Art.-no. DeAgostini_027

DeAgostini

N gauge nickel silver track 100% compatible with Minitrix / Roco / Fleischmann. The 8 tracks make a whole circle. Perfect for helical tracks or the like.

4.99 EUR^*

Art.-no. DeAgostini_043

DeAgostini

N gauge nickel silver track 100% compatible with Minitrix / Roco / Fleischmann. The 8 tracks make a semicircle. Perfect for helical tracks or the like.

4.99 EUR^*

Art.-no. DeAgostini_033

DeAgostini

N gauge nickel silver track 100% compatible with Minitrix / Roco / Fleischmann

- 22.5 ° branch
- 235.2mm radius
- 90 mm length

0.29 EUR^*

Art.-no. DeAgostini_037

DeAgostini

1 pole on/off switch 6A 250V - 1 E4 T85/55

1.99 EUR^*

Art.-no. DeAgostini_038

DeAgostini

N gauge 100% compatible with Minitrix / Roco / Fleischmann - 6-piece set with the following content:
- 2-wire connection cable 100 cm with 2 rail connectors for invisible power supply
- 1-core connection cable 20 cm with a rail connector for invisible power supply
- 4 plastic insulating rail connectors

4.99 EUR^*

Art.-no. DeAgostini_021

DeAgostini

Finished model (including painting) made of polyresin plastic. The illustration shows the model unprocessed. The finished model can thus be placed directly on the system.

6.99 EUR^*

Art.-no. DeAgostini_048

DeAgostini

Finished model (including painting) made of polyresin plastic. The illustration shows the model unprocessed. The finished model can thus be placed directly on the system. The building can also be used as a cowshed or as a horse stable.

4.99 EUR^*

Art.-no. DeAgostini_067

DeAgostini

Finished model (including painting) made of polyresin plastic. The illustration shows the model unprocessed. The finished model can thus be placed directly on the system.

4.99 EUR^*

Art.-no. DeAgostini_068

DeAgostini

Finished model (including painting) made of polyresin plastic. The illustration shows the model unprocessed. The finished model can thus be placed directly on the system.

4.99 EUR^*

Art.-no. DeAgostini_011

DeAgostini

Finished model (including painting) made of polyresin plastic. The illustration shows the model unprocessed. The finished model can thus be placed directly on the system. Windows would only have to be glued in and the lettering glued on as desired. The station and goods shed are separate buildings and can therefore be set up flexibly. The goods shed can also be placed individually.

1.99 EUR^*

Art.-no. DeAgostini_015

DeAgostini

Finished model (including painting) made of polyresin plastic. The illustration shows the model unprocessed. The finished model can thus be placed directly on the system. Tower, canopy, window and other small parts only have to be glued together as desired.

1.99 EUR^*

Art.-no. DeAgostini_041

DeAgostini

inexpensive plastic cars, pre-painted

2.99 EUR^*

Art.-no. DeAgostini_012

DeAgostini

10 pre-painted figures at a great price. 2 packs of 5 different figures are delivered. In total there are probably over 100 different figures, we mix the packs wildly, there is no choice.

1.99 EUR^*

Art.-no. DeAgostini_010

DeAgostini

Four painted cows

1.99 EUR^*

Art.-no. DeAgostini_042

DeAgostini

Four painted horses. Also suitable for a circus.

13.99 EUR^*

Art.-no. Noch_35820

Noch

The mountain is calling - figures 3D printed!
3D Master Figures

The set includes three hikers, three mountain climbers and a summit cross. The hikers are equipped with a walking stick and backpack, while the mountain climbers are on the summit with a climbing harness, helmet and climbing rope. The summit cross included in the set makes each mountain peak appear even more realistic... just like the original!

The set is ideal for creating hiking and climbing scenes on model landscapes and dioramas.

The NOCH 3D Master figures are 3D printed in color! With this fantastic technology, even the smallest details become visible. Whether checked shirts, striped blouses or color gradations and gradients, full-color 3D printing makes it possible.

54.99 EUR^*

Art.-no. Noch_62831

Noch

… gorges and valleys with bridges from NOCH!
Stone arch bridge

The beautiful stone arch bridge fits into many installation situations on your model railway layout thanks to its compact design. The bridge has a single track and can be used for both rail and road traffic. The width of the roadway corresponds to a narrow road, as can still be found in the Alps today.

The laser-cut kit is made of high-quality cardboard and contains detailed assembly instructions as well as the appropriate laser-cut special glue.

Dimensions: 18.5 x 4 cm, 6 cm high

62.99 EUR^*

Art.-no. Noch_63025

Noch

Railway operation like in the original!
Engine shed "Bergün"

The two-stall "Bergün" locomotive shed is located directly next to the station of the same name. There is room for two locomotives in the shed. The gates can be shown open or closed on the model.

The laser-cut model kit is lasered from high-quality cardboard and is supplemented with 3D-printed parts. In addition to detailed assembly instructions, the appropriate laser-cut special glue is included.

Dimensions: 13.9 x 8.4 cm, 6.6 cm high