N-Scale 03/2022: PD10MU DCC Decoder, Fleischmann, Minitrix, Heki

23.99 EUR^*

Art.-no. DH_PD10MU-4

Doehler & Haass

A new Doehler & Haass decoder developed exclusively for Modellbahn Union / DM-Toys, adapted to the needs of N-gauge model railroaders. As with all comparable Doehler & Haass decoders, the driving characteristics of this decoder are at an excellent level. Two small capacitors are installed on the decoder for driving without data loss. Both the software and the chip itself correspond to the same modern technology as the latest decoders from Doehler & Haass. The decoder, produced in Germany, can be used for both normal DC motors and coreless motors. Switching from analogue to digital operation takes place automatically.

Due to our direct sales and exclusive production, we can offer this decoder in cooperation with Doehler and Haass at a very attractive price.

The vehicle decoders support braking with asymmetrical digital voltage (four diodes in series and one diode anti-parallel, Lenz ABC), slow travel (with suitable braking modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®).

Dimensions: 8.5 x 11.7 x 1.8mm
Total load capacity: 1.0 A
Maximum Motor Current: 1.0A
Maximum driving voltage: 30 V
Light function outputs: LV, LR (dimmable): 150 mA each
Function outputs: AUX1, AUX2 (dimmable): 300 mA each

functions
• For operation with conventional DC traction device, digital systems according to the NMRA standard (DCC)
• Switching between analogue and digital operation is automatic
• Short addresses (1-127), long addresses (0001-9999), with 14, 28, 126 speed steps
• Latest generation load control, resulting in particularly smooth control behavior
• Various control variants for optimum adaptation to the engine
• Internally 127 speed steps
• Adjustable motor frequency (low frequency, 16 kHz, 32 kHz)
• Block section operation with simple diodes in digital operation
• Light and function outputs (partially) dimmable and can be activated analogously
• Shunting gear
• Motor, light and track connections can be exchanged electronically
• All function outputs freely programmable
• Temperature protection
• Reset function for DCC
• The decoder can be updated
• Timer for switching off AUX1 and AUX2

The update (the firmware download from the Internet is free) is possible when the decoder is installed on the track (the vehicle does not need to be opened) and is carried out either via the FCC digital center or the programmer. If no appropriate hardware is available, Doehler & Haass will provide a programmer on request.

The vehicle decoders support braking with asymmetrical digital voltage (four diodes in series and one diode anti-parallel, Lenz ABC), slow travel (with suitable braking modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®).

23.99 EUR^*

Art.-no. DH_PD10MU-3

Doehler & Haass

A new Doehler & Haass decoder developed exclusively for Modellbahn Union / DM-Toys, adapted to the needs of N-gauge model railroaders. As with all comparable Doehler & Haass decoders, the driving characteristics of this decoder are at an excellent level. Two small capacitors are installed on the decoder for driving without data loss. Both the software and the chip itself correspond to the same modern technology as the latest decoders from Doehler & Haass. The decoder, produced in Germany, can be used for both normal DC motors and coreless motors. Switching from analogue to digital operation takes place automatically.

Due to our direct sales and exclusive production, we can offer this decoder in cooperation with Doehler and Haass at a very attractive price.

The vehicle decoders support braking with asymmetrical digital voltage (four diodes in series and one diode anti-parallel, Lenz ABC), slow travel (with suitable braking modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®).

Dimensions: 8.5 x 11.7 x 1.8mm
Total load capacity: 1.0 A
Maximum Motor Current: 1.0A
Maximum driving voltage: 30 V
Light function outputs: LV, LR (dimmable): 150 mA each
Function outputs: AUX1, AUX2 (dimmable): 300 mA each

functions
• For operation with conventional DC traction device, digital systems according to the NMRA standard (DCC)
• Switching between analogue and digital operation is automatic
• Short addresses (1-127), long addresses (0001-9999), with 14, 28, 126 speed steps
• Latest generation load control, resulting in particularly smooth control behavior
• Various control variants for optimum adaptation to the engine
• Internally 127 speed steps
• Adjustable motor frequency (low frequency, 16 kHz, 32 kHz)
• Block section operation with simple diodes in digital operation
• Light and function outputs (partially) dimmable and can be activated analogously
• Shunting gear
• Motor, light and track connections can be exchanged electronically
• All function outputs freely programmable
• Temperature protection
• Reset function for DCC
• The decoder can be updated
• Timer for switching off AUX1 and AUX2

The update (the firmware download from the Internet is free) is possible when the decoder is installed on the track (the vehicle does not need to be opened) and is carried out either via the FCC digital center or the programmer. If no appropriate hardware is available, Doehler & Haass will provide a programmer on request.

The vehicle decoders support braking with asymmetrical digital voltage (four diodes in series and one diode anti-parallel, Lenz ABC), slow travel (with suitable braking modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®).

29.99 EUR^*

Art.-no. MU_N-M00513

Modellbahn Union

The Faun L 912/45 A was a military truck made by the German commercial vehicle manufacturer Faun and was part of the 1st generation of wheeled vehicles used by the Bundeswehr. 214 vehicles of this type were delivered to the German Armed Forces between 1958 and 1970 and were mainly used as tractors for low-loader trailers up to 25 t, as well as towing and recovery vehicles. (Q:Wikipedia)

The highly detailed, unpainted model was produced using the 3D printing process and can be processed and painted with standard tools and paints (e.g. with Revell Email or Revell Aqua Color).

19.99 EUR^*

Art.-no. MU_N-A00678

Modellbahn Union

Forging press in two parts as cargo.

The highly detailed, unpainted model was produced using the 3D printing process and can be processed and painted with standard tools and paints (e.g. with Revell Email or Revell Aqua Color).

24.99 EUR^*

Art.-no. MU_N-A00685

Modellbahn Union

Model of an 8000 ton forging press. The press fits our forging manipulator (MU__N-A00699).

The highly detailed, unpainted model was produced using the 3D printing process and can be processed and painted with standard tools and paints (e.g. with Revell Email or Revell Aqua Color).

24.99 EUR^*

Art.-no. MU_N-A00684

Modellbahn Union

Model of a 2500 ton forging press. The press fits our forging manipulator (MU_N-A00699).

The highly detailed, unpainted model was produced using the 3D printing process and can be processed and painted with standard tools and paints (e.g. with Revell Email or Revell Aqua Color).

99.90 EUR (RRP*)

59.99 EUR^*

Art.-no. Liliput_L260113

Liliput

- 6-axis
- ThyssenKrupp
- with yellow and red sliding tarpaulin hood
- company no. 69 346 98-7 and 69 349 98-7

152.10 EUR^*

Art.-no. Minitrix_18219

Minitrix

Prototype: 1 French State Railways (Société national des chemins de fer français / SNCF) express train passenger car, 1st class (A9), 1 express train dining car (Vru), and 1 express train passenger car, 2nd class (B10). As it looked around 1970 with the route "Nice - Paris".

Model: The car has a close coupler mechanism. Prepared for the subsequent installation of interior lighting.
Total length over the buffers 459 mm.

The matching interior lighting: 66616 LED interior lighting.

52.19 EUR^*

Art.-no. Minitrix_18428

Minitrix

Prototype: French State Railways (Société national des chemins de fer français / SNCF) express train passenger car, 2nd class (B10). The train looks as it did around 1970 on the route Nice - Paris.
Model: The car has a close coupler mechanism. Prepared for the subsequent installation of interior lighting. Length over the buffers 153 mm.

The matching interior lighting: 66616 LED interior lighting.

47.69 EUR^*

Art.-no. Minitrix_15492

Minitrix

Prototype: Swiss Federal Railways Cargo Division (SBB Cargo) type Sgns four-axle container flat car. Loaded with 2 coop® refrigerated containers. Operating condition around 2017.
Model: Die-cast metal chassis, type Y 25 bogies, with close coupling mechanisms, loaded with 2 refrigerated containers. Length over the buffers 123 mm.

41.90 EUR (RRP*)

29.99 EUR^*

Art.-no. Fleischmann_814451

Fleischmann

1st class Eurofima carriage of the Italian FS, epoch V. 2018 reissue with a new company number!

With interior. The car is intended for the installation of interior lighting (946901). NEM 355 coupler pocket with short coupling kinematics.

Eurofima car is the name of a comfort car series for international passenger traffic that was jointly procured by a number of Western European railway companies. The vehicles were designed with uniform technical parameters.

117.00 EUR^*

Art.-no. ACME_16515

A.C.M.E.

Model details: - prepared for interior lighting - detailed execution - extensive, elaborate and multicolored imprinting - NEM clutch - close coupling frame

139.99 EUR (RRP*)

99.99 EUR^*

Art.-no. Modemo_NT162

Modemo

22.99 EUR (RRP*)

19.99 EUR^*

Art.-no. Minitrix_18089

Minitrix

Prototype: Czech Railways (CD Cargo) Es 110.8 high-sided gondola car. European standard type with a length of 10.0 m.

Model: With kinematics for close coupling, simplified version.
Length over the buffers 63 mm.

8.54 EUR^*

Art.-no. Busch_8420

Busch

colored plastic model, fixed wheels

12.99 EUR (RRP*)

7.99 EUR^*

Art.-no. Busch_8375

Busch

Super-detailed models with headlights and taillights suitable for the model.

17.98 EUR^*

Art.-no. Lemke_LC4330

Lemke

The VW T3 from Volkswagen was the third generation of the VW van. It was produced from 1979 to 1992 and was the last transporter series with rear-wheel drive. After the VW 411/412 from 1968, the T3 was the last new development of a vehicle from Volkswagen with air-cooled rear engine. Like all VW buses, the third generation also bore the type designation Type 2. Within this series, the individual models T1, T2 and T3 were numbered internally.

In our DM-Toys blog by Christian Weiß, there are more interesting photos and information!

21.60 EUR^*

Art.-no. Artitec_316.098

Artitec

Artitec finished models are built by hand from resin and photo-etched parts. Each model is hand-painted and sometimes slightly aged. The models are in a high collector's quality.

14.99 EUR^*

Art.-no. GF_379-314

Graham Farish

Finished colored plastic models

3.99 EUR^*

Art.-no. Gaugemaster_GM599

Gaugemaster

- Preserves the life of blades
- Encourages accurate cutting
- 3 layer PVC mat in sandwitch structure
- Ensures no cracking or warping
- No slip surface

This cutting mat is constructed from a 3 layer PVC mat in sandwich structure that ensures no cracking or warping. The non slip surface of base holds paper firmly and prevents blade run and cutting error. The use of a cutting mat preserves the life of blades and encourages accurate cutting.

14.99 EUR^*

Art.-no. DM-Toys_17119

DM-Toys

Exclusively at DM-Toys - limiteDModels

MINIS MAN F90 3-axle tractor with rotating axles, window insert and nicely printed.

14.99 EUR (RRP*)

9.99 EUR^*

Art.-no. DM-Toys_17117

DM-Toys

Exclusively at DM-Toys - limiteDModels

MINIS MAN F90 3-axle tractor with rotating axles, window insert and nicely printed.

2.00 EUR^*

Art.-no. FKS_160-915-08

FKS

Long Vehicle and Veiculo Longo warning signs

made using the screen printing process
Sheet with 2 different versions of 16 decals / decals

The warning signs are suitable for all commercially available vehicles on a scale of 1:160.

2.00 EUR^*

Art.-no. FKS_160-915-01

FKS

Truck signs for low-emission/low-noise trucks

made using the screen printing process

The signs can be used on trucks, vans, semi-trailers and trailers

2.00 EUR^*

Art.-no. FKS_160-915-02

FKS

Speed signs, set 1

made using the screen printing process
Sheet with 9 different speed signs (8 pieces each) as wet decals / decals

The speed signs can be used on trucks, vans and agricultural vehicles

2.00 EUR^*

Art.-no. FKS_160-990-07

FKS

Vehicle lettering for fire engines

made using the screen printing process
Sheet with 30 individual water slides / decals

The signs are used to identify fire-fighting vehicles on a scale of 1:160.

2.00 EUR^*

Art.-no. FKS_160-990-04

FKS

Vehicle lettering for fire and rescue vehicles

made using the screen printing process
Sheet with 38 individual water slides / decals

The signs are used to identify fire and rescue vehicles on a scale of 1:160.

2.00 EUR^*

Art.-no. FKS_160-990-03

FKS

Vehicle lettering for fire and rescue vehicles

made using the screen printing process
Sheet with 38 individual water slides / decals

The signs are used to identify fire and rescue vehicles on a scale of 1:160.

2.00 EUR^*

Art.-no. FKS_160-990-02

FKS

Vehicle lettering for fire engines

made using the screen printing process
Sheet with 16 individual water slides / decals

The signs are used to identify fire-fighting vehicles on a scale of 1:160.

6.99 EUR^*

Art.-no. Oxford_NTIL003

Oxford

7.99 EUR^*

Art.-no. Oxford_NTIL002

Oxford

69.99 EUR (RRP*)

49.99 EUR^*

Art.-no. Tomytec_290261

Tomytec

including lighting. 3 AAA batteries required (not included in the set)

Dimensions: 35.5 x 23 x 11.5 cm

59.99 EUR (RRP*)

39.99 EUR^*

Art.-no. Trainworx_55019

Trainworx

The Peterbilt 351 was a series of tractor units built by Peterbilt and produced from 1954 to 1976.

Finished model of the highest quality level with elaborate printing and many small parts installed.

Features:
- rotating wheels
- different supports (loaded / unloaded)
- detailed printing
- the finest window inserts
- Profiled tires
- Wheel nuts reproduced individually
- freestanding exterior mirrors
- freestanding antennas
- free-standing exhaust system
- many separately applied details

43.50 EUR^*

Art.-no. Heki_2196

Heki

The firs are flocked with a special grass fiber - flock mixture that gives the firs a lifelike appearance. A new manufacturing process makes it possible for us to offer you these bulk packs at a sensationally low price.

10.20 EUR^*

Art.-no. Heki_33543

Heki

Grass fiber wild grass 5-6 mm is particularly suitable for simulating overgrown meadows and fields. You get a perfect result when using our Flockstar XL (Art. No. 9510).

10.20 EUR^*

Art.-no. Heki_33544

Heki

Grass fiber wild grass 5-6 mm is particularly suitable for reproducing overgrown meadows and fields. You get a perfect result when using our Flockstar XL (Art. No. 9510).

10.20 EUR^*

Art.-no. Heki_33545

Heki

Grass fiber wild grass 5-6 mm is particularly suitable for reproducing overgrown meadows and fields. You get a perfect result when using our Flockstar XL (Art. No. 9510).

11.50 EUR^*

Art.-no. Heki_15790

Heki

14X28cm

decovlies wild grass is a ground cover mat consisting of an almost invisible carrier material onto which 5-6 mm long grass has been electrostatically applied.
As a supplement to our shades of green, you can now also get three shades of autumn.
The ground cover mat always has a minimum size of 392 cm² and consists of one or more pieces.

11.50 EUR^*

Art.-no. Heki_15791

Heki

14X28cm

decovlies wild grass is a ground cover mat consisting of an almost invisible carrier material onto which 5-6 mm long grass has been electrostatically applied.
As a supplement to our shades of green, you can now also get three shades of autumn.
The ground cover mat always has a minimum size of 392 cm² and consists of one or more pieces.

11.50 EUR^*

Art.-no. Heki_15792

Heki

14X28cm

decovlies wild grass is a ground cover mat consisting of an almost invisible carrier material onto which 5-6 mm long grass has been electrostatically applied.
As a supplement to our shades of green, you can now also get three shades of autumn.
The ground cover mat always has a minimum size of 392 cm² and consists of one or more pieces.