Dear customer,
All items you can see in our online shop are in stock and can be delivered immediately. We deliver via DHL & UPS without delays.
38.86 EUR*
Art.-no. DH_DH10C-1
Doehler & Haass
The latest version with the latest software is always delivered!
The software, firmware and sound data download can be obtained from the Doehler & Haass website . Product features and functions - For optional operation with conventional DC driving device, digital systems according to SelecTRIX 1 and 2 or according to NMRA standard (DCC) -The switchover between analog and digital operation takes place automatically -In digital mode, the last programmed system is used (it is not switched automatically!) -SelecTRIX 1 31 speed steps, 100 addresses -SelecTRIX 2 127 speed steps, 10,000 addresses, 16 additional functions -DCC Short addresses (1-127), long addresses (0001-9999), with 14, 28, 126 speed steps - The latest generation of load control, resulting in particularly smooth control behavior -Various control variants for optimal adaptation to the engine -Internal 127 speed steps -Adjustable motor frequency (low frequency, 16 kHz, 32 kHz) -Block section operation with simple diodes in digital operation -Light and function outputs can be dimmed and activated analogously - Shunting -Motor, light and track connections can be exchanged electronically -All function outputs are freely programmable -Temperature protection -Reset function for DCC and SX2 -Update capability of the decoder -The update (the firmware download from the Internet is free) is possible with the decoder installed on the track (no opening of the vehicle necessary) and is carried out either via the FCC digital center or the programmer. If no corresponding hardware is available, Doehler & Haass will provide a programmer on loan on request. The DH10C vehicle decoder supports braking with asymmetrical digital voltage (four diodes in series and one anti-parallel diode, Lenz ABC), slow travel (with suitable brake modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®). A connected SUSI sound module must be removed for SX1 programming. It is sufficient to interrupt the supply voltage (red wire) for the time of the SX1 programming. The SX2 or DCC programming is not affected by this. Technical data (2nd generation) DH10C Dimensions [mm] 12.7 x 8.9 x 1.4 Total load 1.5 A Maximum motor current 1.5 A. Maximum driving voltage 30 V. Function outputs light: LV, LR (dimmable) 150 mA each Function outputs: AUX1, AUX2 (dimmable) 300 mA each Function outputs: AUX3, AUX4 1.0 A each Function outputs: AUX5, AUX6 With SUSI interface (if AUX5 / AUX6 deactivated) unamplified *) Connection variants: -DH10C-0 Without connecting wires -DH10C-1 With ribbon cable for standard socket NEM651 -DH10C-2 With connection cable for standard socket NEM651 -DH10C-3 With pigtail -DH10C-4 6-pin plug connector for direct plugging (NEM651) |
39.81 EUR*
Art.-no. DH_DH10C-3
Doehler & Haass
The latest version with the latest software is always delivered!
The software, firmware and sound data download can be obtained from the Doehler & Haass website . Product features and functions - For optional operation with conventional DC driving device, digital systems according to SelecTRIX 1 and 2 or according to NMRA standard (DCC) -The switchover between analog and digital operation takes place automatically -In digital mode, the last programmed system is used (it is not switched automatically!) -SelecTRIX 1 31 speed steps, 100 addresses -SelecTRIX 2 127 speed steps, 10,000 addresses, 16 additional functions -DCC Short addresses (1-127), long addresses (0001-9999), with 14, 28, 126 speed steps - The latest generation of load control, resulting in particularly smooth control behavior -Various control variants for optimal adaptation to the engine -Internal 127 speed steps -Adjustable motor frequency (low frequency, 16 kHz, 32 kHz) -Block section operation with simple diodes in digital operation -Light and function outputs can be dimmed and activated analogously - Shunting -Motor, light and track connections can be exchanged electronically -All function outputs are freely programmable -Temperature protection -Reset function for DCC and SX2 -Update capability of the decoder -The update (the firmware download from the Internet is free) is possible with the decoder installed on the track (no opening of the vehicle necessary) and is carried out either via the FCC digital center or the programmer. If no corresponding hardware is available, Doehler & Haass will provide a programmer on loan on request. The DH10C vehicle decoder supports braking with asymmetrical digital voltage (four diodes in series and one anti-parallel diode, Lenz ABC), slow travel (with suitable brake modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®). A connected SUSI sound module must be removed for SX1 programming. It is sufficient to interrupt the supply voltage (red wire) for the time of the SX1 programming. The SX2 or DCC programming is not affected by this. Technical data (2nd generation) DH10C Dimensions [mm] 12.7 x 8.9 x 1.4 Total load 1.5 A Maximum motor current 1.5 A. Maximum driving voltage 30 V. Function outputs light: LV, LR (dimmable) 150 mA each Function outputs: AUX1, AUX2 (dimmable) 300 mA each Function outputs: AUX3, AUX4 1.0 A each Function outputs: AUX5, AUX6 With SUSI interface (if AUX5 / AUX6 deactivated) unamplified *) Connection variants: -DH10C-0 Without connecting wires -DH10C-1 With ribbon cable for standard socket NEM651 -DH10C-2 With connection cable for standard socket NEM651 -DH10C-3 With pigtail -DH10C-4 6-pin plug connector for direct plugging (NEM651) |
59.99 EUR*
Art.-no. MU_N-B00132
Modellbahn Union
Model of an island train station. Island stations are stations whose entrance buildings are located in an island position between the tracks. The building, which is surrounded on both sides by the track field, is then usually accessed from the street side via a dead end street, which branches off from a street that crosses or undercrosses the tracks. Our model is particularly suitable for detailed interior design thanks to the generously sized windows. Platform length without ramp: 268.5 mm
|
14.99 EUR*
Art.-no. MU_N-B00135
Modellbahn Union
Set with 2 extension parts for the Inselbahnhof platform MU_N-B00132
|
129.99 EUR*
Art.-no. MU_N-B00070
Modellbahn Union
Our model is based on the jetties which, up to the 1970's, stood in the harbour of Sassnitz (Rügen).Contrary to the original our model has only 1 track. The prototype had a y-point on the second bridge segment, facilitating ferries with 2 track cargo bays. Although only 2 generalised sketches exist we have been able to reproduce the complex construction of the bridge. A jetty serves the loading of ferries and is constructed in such a way that the water level differences between tides can be overcome, making it possible to load the ferries at any given time.The jetties in Sassnitz contained two bridge segments, making it highly flexible.The first bridge was operated by means of two motors driving two worms, the second one used cables and contra weights. The model is constructed in such a way that it is moveable, giving you the opportunity to fix the bridge at any height. The kit includes 3D printed motors and worms. For building this kit expierence is advised!
|
79.99 EUR*
Art.-no. MU_N-B00072
Modellbahn Union
Small version of our ferry jetty (MU_N-B00070) which consists of only 1 bridge segment. The total length is limited to 175mm, making it suitable for smaller layouts. For building this kit expierence is advised!
|
14.99 EUR*
(0.032m², base price 468.44 EUR/m²)
Art.-no. MU_N-L00204
Modellbahn Union
Set of 3 cobblestone slabs engraved in great detail. The plates are an excellent match for our Landungsbrücken MU_N-B00070 and MU_N-B00072, for example.
|
7.99 EUR*
Art.-no. MU_N-C10001
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 38 x 15 x 16 mm, pin spacing according to NEM 380 36.5x14mm |
7.99 EUR*
Art.-no. MU_N-C10002
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 38 x 15 x 16 mm, pin spacing according to NEM 380 75x14mm |
7.99 EUR*
Art.-no. MU_N-C10003
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 38 x 15 x 16 mm, pin spacing according to NEM 380 36.5x14mm |
7.99 EUR*
Art.-no. MU_N-C10004
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 38 x 15 x 16 mm, pin spacing according to NEM 380 36.5x14mm |
7.99 EUR*
Art.-no. MU_N-C10005
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 38 x 15 x 16 mm, pin spacing according to NEM 380 36.5x14mm |
7.99 EUR*
Art.-no. MU_N-C10006
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 38 x 15 x 16 mm, pin spacing according to NEM 380 36.5x14mm |
7.99 EUR*
Art.-no. MU_N-C10007
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 38 x 15 x 16 mm, pin spacing according to NEM 380 36.5x14mm |
7.99 EUR*
Art.-no. MU_N-C10008
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 38 x 15 x 16 mm, pin spacing according to NEM 380 36.5x14mm |
7.99 EUR*
Art.-no. MU_N-C00011
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 76x 15x 16 mm, pin spacing according to NEM 380 75x14mm |
7.99 EUR*
Art.-no. MU_N-C00012
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 76x 15x 16 mm, pin spacing according to NEM 380 75x14mm |
7.99 EUR*
Art.-no. MU_N-C00013
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 76x 15x 16 mm, pin spacing according to NEM 380 75x14mm |
7.99 EUR*
Art.-no. MU_N-C00014
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 76x 15x 16 mm, pin spacing according to NEM 380 75x14mm |
7.99 EUR*
Art.-no. MU_N-C00015
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 76x 15x 16 mm, pin spacing according to NEM 380 75x14mm |
7.99 EUR*
Art.-no. MU_N-C00016
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 76x 15x 16 mm, pin spacing according to NEM 380 75x14mm |
7.99 EUR*
Art.-no. MU_N-C00017
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 76x 15x 16 mm, pin spacing according to NEM 380 75x14mm |
7.99 EUR*
Art.-no. MU_N-C00018
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 76x 15x 16 mm, pin spacing according to NEM 380 75x14mm |
7.99 EUR*
Art.-no. MU_N-C00019
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 76x 15x 16 mm, pin spacing according to NEM 380 75x14mm |
7.99 EUR*
Art.-no. MU_N-C00020
Modellbahn Union
Execution:
- completely painted and printed - Removable cover Dimensions: 76x 15x 16 mm, pin spacing according to NEM 380 75x14mm |
0.50 EUR*
Art.-no. Fleischmann_992120
Fleischmann
New N-gauge catalog with 108 pages
|
0.20 EUR*
Art.-no. Fleischmann_80694
Fleischmann
New N-gauge catalog with 18 pages
|
0.25 EUR*
Art.-no. Fleischmann_83048
Fleischmann
New N-gauge catalog with 32 pages
|
0.79 EUR*
Art.-no. Fleischmann_00779141
Fleischmann
1 piece
|
1.25 EUR*
Art.-no. Fleischmann_00559141
Fleischmann
Switching lever for switch 1x
|
239.99 EUR*
Art.-no. Tomix_98695
Tomix
Contents: 6-piece train set equipped with: |
239.99 EUR*
Art.-no. Tomix_98716
Tomix
Contents: 6-piece train set equipped with: |
149.99 EUR*
Art.-no. Tomix_98717
Tomix
Contents: 5-piece train set equipped with: |
39.99 EUR*
Art.-no. Kato_23-514
Kato
Kato Gauge N Set of 2 stackers |
39.99 EUR*
Art.-no. Kato_23-515
Kato
Kato Gauge N Set of 2 stackers |
39.99 EUR*
Art.-no. Kato_23-516
Kato
finish: |
39.99 EUR*
Art.-no. Kato_23-517
Kato
Kato Gauge N
Execution: Finished model, colored, with decal sheet Forks and stem are moveable. |
26.99 EUR*
Art.-no. Gabor_12332604
Gabor
Ready-made model made of plastic, with window insert. The front wheels can be steered in order to represent different construction site scenarios.
|
29.99 EUR*
Art.-no. Gabor_12332402
Gabor
Finished model made of plastic, with window insert. In addition, a spare wheel and a hydraulic ram are included for illustration in some operating situations. The front wheels can be steered to represent different construction site situations.
|
29.99 EUR*
Art.-no. Gabor_12332401
Gabor
Finished model made of plastic, with window insert. In addition, a spare wheel and a hydraulic stamp are included for display in some operating situations. The front wheels can be steered to show different construction site situations.
|
34.99 EUR*
Art.-no. Gabor_12333301
Gabor
Finished model made of plastic, with window insert. The front wheels can be steered to show different driving situations.
|
19.99 EUR*
Art.-no. Gabor_12130604
Gabor
Ready-made model made of plastic, with window insert.
|
11.99 EUR*
Art.-no. Loewe_2078
Loewe
Elaborately printed on both sides according to the prototype, stored on wooden transporters and secured with straps, suitable for all common 2-axle flat, low side and stake wagons, length: 60 mm
|
12.99 EUR*
Art.-no. Loewe_2079
Loewe
Elaborately printed on both sides according to the prototype, stored on wooden transport and secured with straps, suitable for all common 4-axle flat, low-side and stake wagons, length: 110 mm
|
Yours sincerely
Daniel Mrugalski
DM-Toys